Board Setup

How to Hang a Dartboard on a Door

Hang a dartboard on a door with an over-door hanger or screws into a solid door. Set the bull at 1.73 m and follow the safety rules before you throw.

On this page
  1. The short answer
  2. Check the door first
  3. Option 1: an over-door hanger
  4. Option 2: screws into a solid door
  5. Set the height from the floor
  6. Steady the door
  7. Clearance
  8. Mark the throw line
  9. Safety
  10. Mistakes to avoid

The short answer

Yes, with conditions. You can use an over-door hanger, or screw the bracket into a solid-core or solid-timber door. Do not use a hollow-core door. Set the bull at 1.73 m (5 ft 8 in) from the floor, and keep the door out of use while anyone is throwing.

Check the door first

The type of door matters more than anything else:

  • Hollow-core doors have a skin only about 3 to 5 mm thick. Darts dent and puncture it, and screws hold poorly. Avoid them.
  • Solid-core and solid-timber doors take screws and impact much better.
  • Interior doors are typically about 35 mm (1⅜ in) thick in the UK and US. Check that the hanger fits your door’s thickness.
  • Fire doors must close freely and must not be modified. Do not hang anything on one.

Option 1: an over-door hanger

An over-door hanger hooks over the top of the door, and the board hangs on the face of the door. The general steps are:

  1. Assemble the top brackets and the vertical slider, leaving the screws slightly loose.
  2. Set the slider so the bull sits at 1.73 m from the floor.
  3. Hook the hanger over the door and adjust the top brackets to the door’s thickness. Tighten them so the frame does not wobble.
  4. Mount the board on the hanger. Use foam wedges or grip pads to keep it steady.

Over-door hangers add a small gap at the top, so check that the door still closes and latches properly.

Option 2: screws into a solid door

On a solid-core or solid-timber door, you can fix the bracket with screws instead of a hanger. Mark the bull height first, then drill pilot holes, fit the bracket and check that it is level. This is a permanent fixing, so check that the door is solid before you start.

Set the height from the floor

Measure the bull height up from the floor, not down from the top of the door. Many hangers are set too high or too low, which makes the throw awkward. The dartboard height guide explains how to measure the bull.

Steady the door

A door that rattles or swings reduces accuracy. A doorstop or a wedge helps keep it still. Felt pads or foam behind the board and bracket protect the door and reduce impact noise.

Clearance

Check the clearance when the door is moved. The board and surround should not hit the frame, the handle or the hinges when the door opens or closes. Lighter boards, such as electronic or paper boards, suit doors better than heavy cabinets.

Mark the throw line

Measure 2.37 m (7 ft 9¼ in) from a point on the floor directly below the bull for steel tip, or 2.44 m (8 ft) for soft tip. If the board hangs plumb, that point lines up with the board face. The oche distance guide explains where to stand.

Safety

  • Lock the door or block access from the other side during play. Someone who opens the door walks into the line of fire.
  • Never use a fire door.
  • Check the hanger before every session, especially if the door gets a lot of use.

Mistakes to avoid

  • Thinking any door can take a bristle board and surround. Check the door type first.
  • Measuring the height from the top of the door. Measure from the floor.
  • Assuming an over-door hanger is at regulation height by default. Set the bull yourself.
  • Ignoring the door’s movement. A moving door changes the board’s alignment.

For a no-drill option that does not use a door, see how to put a dartboard up without a drill. The full setup is in the dartboard setup guide.

The complete guide to board setup

How to Set Up a Dartboard: Height and Throwing Distance
Read the guide

Keep exploring

Guides from other topics

All topics →