Board Setup

How to Fit a Dartboard Surround or Mount a Board in a Cabinet

Fit a dartboard surround by removing the board or clipping segments, and mount a cabinet level with the bull at 1.73 m. Clear steps and common mistakes.

On this page
  1. What a surround does
  2. Check the size first
  3. Fitting a one-piece surround
  4. Fitting a segmented surround
  5. Mounting a board in a cabinet
  6. A flush finish with a recessed backboard
  7. Distance and cabinet doors
  8. Mistakes to avoid

What a surround does

A surround is a ring of foam, usually EVA or polyurethane, that sits around the edge of the board. It catches stray darts that would otherwise hit the wall. Surrounds do not change the throw distance or the bull height, but they do add thickness around the board, so check the fit before you hang it.

Check the size first

A surround is sized for a standard bristle board. The inner diameter is usually 17¾ to 18 in (451 to 457 mm). The outer diameter is roughly 28 to 30 in (71 to 76 cm), but it varies by model. Check that the surround matches your board before you buy it.

Electronic boards usually do not need a surround.

Fitting a one-piece surround

A one-piece surround goes on over the edge of the board, so the board has to come off the wall first:

  1. Remove the board from the bracket.
  2. Stretch the surround over the edge of the board, working around it evenly.
  3. Rehang the board and check the bull height again.

A thick or raised number ring can stop the surround from seating flush. Some brackets can do the same. If the surround sits proud, check the ring and bracket before you force it.

Fitting a segmented surround

A segmented surround, often in four pieces, clips together around the board. You can fit it while the board is still mounted, which makes it the easier option for a board that is already on the wall. Clip each segment in turn, then check that the segments meet evenly around the board.

Mounting a board in a cabinet

A cabinet is a box with doors and a back panel, and it usually has a scoreboard inside. The board mounts on the centre bracket inside the cabinet.

  1. Level the cabinet first. Fix it to the wall with 2 to 4 screws through the back panel, using fixings suited to your wall type.
  2. Mount the board on the cabinet’s internal centre bracket, then fit the stabilising clips.
  3. Set the bull, not the cabinet. Position the cabinet so the bull sits at 1.73 m (5 ft 8 in). The bull is not always at the cabinet’s centre, so do not assume it is.
  4. Align the board inside the cabinet, then check that it is level and plumb.

A cabinet with its board and darts weighs roughly 10 to 15 kg, and the weight varies by model. Get help when you lift it onto the wall.

A flush finish with a recessed backboard

A darts forum builder described a DIY backboard that gives a flush finish. They cut a 29 in square of ¾ in plywood, drilled a hole for the board’s fixing screw, and cut a board-sized circle out of the middle so the board sat flush. They covered the plywood in felt and fitted the surround on top. They noted that the depth of the plywood depends on the thickness of the board and the surround. With thicker felt, they said they would have used 5/8 in plywood instead, to keep everything flush.

This is one builder’s method, not a standard. If you want a flush finish, check the depth of your board and surround first, then make a test fit before you fix anything permanently.

Distance and cabinet doors

The throw distance is measured from the face of the board, not from the cabinet back or the wall, so the cabinet depth matters. Check the throw line after the cabinet is hung. See the oche distance guide for where to stand.

Cabinet doors open into the throwing area. Keep them fully open or out of the lane while you play. Open doors also take up width, roughly 1.2 to 1.5 m, so plan the room for them. The space guide covers the figures.

Mistakes to avoid

  • Assuming every surround fits every board. Check the size, and remember that electronic boards usually need none.
  • Assuming the cabinet’s centre is the bull. Measure the bull and set it at 1.73 m.
  • Assuming a surround stops every dart. Wide misses still reach the wall, so a backboard helps. See what to put behind a dartboard.
  • Measuring the throw distance from the cabinet back. Measure from the board face.

For the full sequence, see the dartboard setup guide.

The complete guide to board setup

How to Set Up a Dartboard: Height and Throwing Distance
Read the guide

Keep exploring

Guides from other topics

All topics →